Saturday, August 8, 2015

Quilled Poinsettia Flower Ornament

As I noted in my last post, there is a need for quilled Christmas tree ornaments for a "Quilled Ornament Charity Project."  Click the link for details about the project, and to see if you might be interested in participating!

I have decided to make two ornaments for the project.  The first is this quilled poinsettia flower ornament.  It is a simple design, but it looks really lovely now that it is all finished.  I thought I'd present a tutorial here of what I did, so anyone could make one.  Although I've done plenty of live presentations and workshops, this is the first written tutorial I've really done for quilling, so here it goes.

Here's what you'll need ...
  • Five full strips of dark red quilling paper, 1/4 of an inch wide.  
  • Five full strips of light red quilling paper, also 1/4 of an inch wide.  
  • One bright yellow strip, 4 inches long and 1/8 of an inch wide.  
  • One full strip of green with gold edging, 1/8 inch wide, and another half of a strip of the same color.
  • Glue, I use a good quality white craft glue.
  • Ideally, a clear acrylic spray to finish the ornament 
Roll the dark red strips and form them into 'leaf' shapes.  Glue the ends of the petals together to form a five-petaled flower, as shown.  Roll the light red strips and also make 'leaf' shapes.  Glue these together to form another five-petaled flower.

Now, you can see my light red flower is a bit smaller than the dark red flower.  This was intentional.  My dark red paper is very heavy, making a larger coil when it unwinds, and my light red paper is light, rolling tightly and not unwinding so much.  So even though the strips are the same length, the petals for the light red flower layer are somewhat smaller.  If you are dealing with paper that is the same weight for each color, you'll want to take some of the length off of your light red strips to achieve this effect.  I've placed a quarter in the image to give a sense of scale, both so you can see the difference in sizes a little better, and so you can see the size of the whole design.  It's more than four inches across at this point.

After the two 'flowers' have dried, stack the light red, smaller layer on top of the larger dark red layer and glue them together, staggering the petals.  You might have to be clever with small dabs of glue here and there to ensure the design is sturdy enough to hang from a tree, but doesn't look like it has glue all over it.

Then roll the bright yellow strip into a simple open circle quill and glue that to the center of the design.  This was where I'd originally intended to stop.  I added a silver jump ring at the top so it could dangle from the tree.  But then I took another look and decided the piece needed a but more 'oomph.'  So I chose to put a pair of leaves on it.  Roll the two green/gold gilded strips and make leaf shapes, as shown.  One will be smaller than the other, of course, because the strips are not the same length.  You might need to be careful about gluing them.  I had to add extra glue to the backs (the not-gold side) to make sure that they didn't 'spring out' like, well, springs, anytime the design was bumped or dropped.  (I put it through a few tests ...)

Then I glued them between the bottom petals of the flower, keeping them flat on the work surface.  They added just the extra interest and 'bling' I was looking for.  Then I coated the design with about three light coats of clear acrylic sealer.  I use Krylon Gloss UV protective clear coating for most of my quilling.  I like the way it tends to enhance the colors while adding a bit of a sheen.  Excellent in this case, athough I use the 'matte' finish rather than the 'gloss' in some situations.

Finished!  It's about five inches from top to bottom, and has a nice sturdy feel to it.  I hope it shows up well on a six foot tree, and has the durability to survive the whole auctioning process :)

Image Credit - My photos of my new poinsettia flower ornament!

5 comments:

  1. I know next to nothing about quilling, but that ornament is gorgeous.It's perfect for the charity auction; someone is going to love it.

    ReplyDelete
  2. Thanks! I hope it goes well on the tree. I especially hope I made it durable. I used rather a bit more glue that I normally do, hoping it holds together even with some handling.

    ReplyDelete
  3. Thank you, Ann! I like how it came out, even with this simple design.

    ReplyDelete

Hello! Thank you so much for visiting my blog and leaving a comment! I ask that all comments be relevant the content of my blog. Comments that are not relevant, spam, just there to sell something, etc., will be removed. Happy Arts and Crafting!

Note: Only a member of this blog may post a comment.